060-1650 Motor Home Entrance Door Hardware

Designed for RV motor homes and fifth wheel trailer entrance doors, this product has been upgraded with a steel plunger for better security and long life. It features easy installation with through sandwich mounting, a low-profile plunger style latch which is compliant to FMVSS 206, a built-in deadbolt for additional security and is power lockable.

 

Designed For

  • Motor home entrance doors with thickness ranging from 1.39" (35.3mm) to 1.78" (45.2mm)
  • Different inside handle assemblies are required to facilitate the range of door thicknesses. Please identify when inquiring
  • Universal application - can be used in either right or left-hand doors


Features/Benefits

  • Inside release is low profile .940"(23.9mm) to allow for close-fitting screen doors
  • Paddle can be locked before door is shut and is rigid when locked
  • Inside assist with open bail for easy closing
  • Can be keyed to match other TriMark door products with KeyOne Plus for a single-key system, keyed alike or provided non-locking
  • Built-in deadbolt eliminates the need for add-on residential type deadbolt (deadbolt option)
  • Deadbolt locks into the fully extended position for true deadbolt functioning (deadbolt option)
  • Ability to be used with power actuation for locking
  • Deadbolt cylinder non-removable when locked for added security

Available

  • With optional built-in deadbolt
  • Master keyed paddle key cylinder and non-master keyed deadbolt key cylinder

 

Material

  • Housing, inside plates, handles, deadbolt, locking components including lock knobs: Die cast zinc alloy
  • Strike plate: Heat treated and zinc plated steel
  • Plunger load pins and plunger end plates: Steel

Finish

  • Black powder coated
  • Copper-nickel-chrome plated
  • Other finishes available upon request

Installation

  • #10-24 UNC mounting screws (not included). Recommended torque 10 in/lbs (1.1 N-m)
  • 1/4-20 UNC grade 5-type fasteners for strike plate installation recommended
  • Supplied with gaskets already installed
  • Sandwich mount installation does not require any linkage rods

U.S. Patent No. 8,733,139

U.S. Design Patent No. D674,678 / D676,304

Applications of this system may fall within the requirements of FMVSS 206 (ECE R11) and SAE J839 safety standards These safety related requirements are dependent on door application, e.g. front and rear hinged doors, sliding doors, or hinged upward swinging doors. The entire door hardware system must be included in the design/analysis process: latch, handle, lock mechanism, cables/rods/linkages, fasteners, hinges, etc. This ensures compatibility of all components within the hardware system. If FMVSS 206 (ECE R11) is a requirement, then all of the components within the door system must comply with strength, inertia and locking requirements as specified within the Standard. Note that this product complies with FMVSS 206 (ECE R11) when tested in accordance with SAE J839 and that this system meets FMVSS 206 (ECE R11) loads and locking requirements and may be used in FMVSS 206 (ECE R11) applications pending TriMark application approval

典型用途

典型应用用途图解按照行业/系统组织,目的在于给予用户指定采用TriMark产品的完整系统的一些思路。

不是所有行业/系统应用都具有典型用途图解。如果你的特定应用没有典型应用图解,请提交一份产品技术信息请求,我们的一位技术代表可以帮助您选择一个适用于您的特定应用的产品解决方案。

060-1650 Motor Home Entrance Door Hardware

  • 旅行房车

    外部人员进出门


  • 旅行拖车 /拖车活动房屋

    外部人员进出门


请设置过滤条件:


    ©2024 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale