050-0850 TriGuard Heavy Duty Latch Module with Slam Cam Option

This heavy duty latch module is designed for medium to heavy-duty entrance and rear door applications. It features a proven single rotor latch design and high strength 8 gauge (4.2mm) front mounting plate with flange mounting.

Designed For

  • Medium to heavy duty doors greater than 200 lbs. (91 kg) with door seal pressures of 50-150 lbs. (23-60 kg)
  • Use with TriMark 070-0201 Striker Bolt

Features/Benefits

  • Heavy duty modular construction - survives in punishing environments
  • Can be used on retrofit or new surface mount vehicle construction  
  • Heavy duty latch/striker with self-aligning "slam cam" provides rotor/cam assist to heavy doors, hinges and compensates for door sag

Available

  • Right or left hand configurations (right hand shown)
  • Striker with self-aligning “slam cam”
  • Replaceable striker alignment lift blocks
  • Custom configured release levers

Material

  • Case halves: high strength steel
  • Springs: Non-corrosive stainless steel

Finish

  • Zinc plated, clear chromate steel components

Installation

  • (4) M8 x 1.25 class 8.8 or better fasteners are recommended (not included)
  • Tighten to the manufacturers' recommended torque value

U.S. Patent No. 7,938,458

Applications of this latch may fall within the requirements of FMVSS 206 (ECE R11) and SAE J839 safety standards. These safety related requirements are dependent on door application, e.g. front and rear hinged doors, sliding doors, or hinged upward swinging doors. The entire door hardware system must be included in the design/analysis process: latch, handle, lock mechanism, cables/rods/linkages, fasteners, hinges, etc. This ensures compatibility of all components within the hardware system. If FMVSS 206 (ECE R11) is a requirement, then all of the components within the door system must comply with strength, inertia and locking requirements as specified within the Standard. Note that this product complies with FMVSS 206 (ECE R11) when tested with approved TriMark Striker Bolts in accordance with SAE J839 and that this product meets FMVSS 206 (ECE R11) load requirements and may be used in FMVSS 206 (ECE R11) applications pending TriMark application approval

 

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

050-0850 TriGuard Heavy Duty Latch Module with Slam Cam Option

  • Armored Vehicle

    Exterior Personnel Doors

    Interior Personnel Doors

    Rear Doors


  • Construction - Heavy Earthmoving

    Exterior Personnel Doors


  • Construction - Lifting and Material Handling

    Exterior Personnel Doors


  • Construction - Light Earthmoving

    Exterior Personnel Doors


  • Industrial Enclosure/Cabinet

    Access Panels

    Exterior Storage Compartments


Please specify search criteria:


CompareCatalog NumberTriMark NumberDescriptionStatus CodeSample RequestCAD Drawing
0500850-101508-23329-2333023311-01Right Hand,Zinc Plate/Clear Chromate,M8 Exterior Flange Mounting (4),L-Shaped,Non-handed,2.12 x .77 x .204 DIA hole,(53.8 mm x 19.6 mm x 5.2 mm Dia Hole),Offset,Right Hand,10.6mm Offset,32.6mm x 0.5mm x 5.25mm Dia Hole,(.42 Offset,1.28 x .02 x .21 DIA Hole)A/A
0500850-201508-23329-2333123312-01Left Hand,Zinc Plate/Clear Chromate,M8 Exterior Flange Mounting (4),L-Shaped,Non-handed,2.12 x .77 x .204 DIA hole,(53.8 mm x 19.6 mm x 5.2 mm Dia Hole),Offset,Left Hand,10.6mm Offset,32.6mm x 0.5mm x 5.25mm Dia Hole,(.42 Offset,1.28 x .02 x .21 DIA Hole)A/A
©2018 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale