020-1150 Two Point Free Float Pull Handle

This product is designed for entrance doors on RV and specialty vehicles where it is desirable to have the exterior handle remotely mounted from the inside release and rotary latch. It features a large automotive styled exterior pull handle and is adaptable for power locking.

Designed For

  • Entrance and compartment doors with thickness of 2.00“ (50.8mm) minimum

Features/Benefits

  • Automotive style pull handle and latch mechanism
  • Smooth opening/closing action
  • Comfortable finger access
  • Adaptable for power door lock actuation
  • Non-handed design
  • The pull handle can be mounted in vertical or horizontal orientation  
  • Molded gasket for flange of housing and paddle leg provides resistance to water infiltration

Available

  • Master keyed lock key cylinder
  • Lock can be keyed to match other TriMark door products with KeyOne-- Plus for a single-key system, keyed alike or provided non-locking

 

Installation

  • Easy to install with (4) #8-32 UNC mounting screws (not included)
  • Recommended mounting torque 30 in-lbs (3.4 N-m)

Finish

  • Black powder coated housing with black powder coated paddle or chrome plated paddle
  • Optional chrome plated housing

Material

  • Sturdy die cast zinc alloy paddle and housing
  • Molded gaskets (included)

U.S. Design Patent No. D564,855

Applications of this product may fall within the requirements of FMVSS 206 (ECE R11) and SAE J839 safety standards. These safety related requirements are dependent on door application, e.g. front and rear hinged doors, sliding doors, or hinged upward swinging doors. The entire door hardware system must be included in the design/analysis process: latch, handle, lock mechanism, cables/rods/linkages, fasteners, hinges, etc. This ensures compatibility of all components within the hardware system. If FMVSS 206 (ECE R11) is a requirement, then all of the components within the door system must comply with strength, inertia and locking requirements as specified with the Standard. Note that this product complies with FMVSS 206 (ECE R11) when tested in accordance with SAE J839 and that this product meets FMVSS 206 (ECE R11) locking requirements and may be used in FMVSS 206 (ECE R11) applications pending TriMark application approval.

 

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

020-1150 Two Point Free Float Pull Handle

  • Bus / Motorcoach / Mass Transit

    Baggage Doors

    Exterior Personnel Doors


  • Fire / Rescue / Ambulance / Emergency Vehicle

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Motor Homes

    Baggage Doors

    Exterior Personnel Doors


  • Trailers - Ranch / Farm / Cargo / Utility

    Exterior Personnel Doors


  • Travel Trailer / 5th Wheel

    Exterior Personnel Doors


Please specify search criteria:


CompareCatalog NumberTriMark NumberHandingFinishKey CodePivot PlateMountingStatus CodeSample RequestCAD Drawing
0201150-3037-700000000-2124718-05 Non-Handed Low Gloss Black KeyOne Plus provision - no lock installed Left Hand Pivot Actuation Horizontal Handle Mounting With Vertical Rod PullA/A
0201150-3063-700000000-2124718-04 Non-Handed Copper-Nickel Nickel Chrome KeyOne Plus provision - no lock installed Left Hand Pivot Actuation Horizontal Handle Mounting With Vertical Rod PullA/A
©2018 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale