• Home
  • 070-1000 8mm Hoop Strike

070-1000 8mm Hoop Strike

The 070-1000 8mm Hoop Strike is designed as a companion part for use with TriMark's single rotor latches that requires an 8mm diameter strike and compliance to FMVSS 206.

Features/Benefits

  • Automotive style hoop-type strike features low profile and minimizes clothing snag hazard
  • Base mounted style provides a rigid base for strike support
  • Welded construction and heat treat exceeds FMVSS 206 loads 

Available

  • 43mm high x 57mm long base
  • Other versions available; please inquire 
  • Backer mount plate is available to facilitate strike mounting and adjustability (Part # 35285) (not included)

Material

  • Hoop material is medium carbon steel, heat treated for strength and long life

Installation

  • (2) M6 x 1 class 10.9 flat head fasteners are required (not included)
  • Tighten to the fastener manufacturers' recommended torque value, however, do not exceed 135 in-lbs (15.0 N-m)
  • It is recommended that the hoop strike is mounted to the aperture with the TriMark Backer Mount Plate corresponding to hoop strike (Part # 35285) (not included)
  • Note: Aligning the latch and the hoop strike is KEY to proper latch function

Finish

  • Zinc plated with clear chromate
  • Black e-coat

Latch & Hoop Strike Installation

  • Install hoop strike in door frame (it is recommended to use TriMark Backer Mount Plate on the inside of the door jamb to facilitate mounting and adjustability - Part # 35285) (not included)
  • Close door carefully and check for interference between head of hoop strike and latch components
  • Adjust hoop strike vertically so door is not guided upward or downward while being closed (See AP050-1900 Application Guide)
  • CHECK TO DETERMINE THAT BOTH SECONDARY AND PRIMARY LATCHING POSITIONS ARE USABLE
  • Door should be latched but not "closed" in secondary position and latched to anticipated "closed" position with respect to adjacent surfaces in primary position
  • If both primary and secondary positions are not evident, readjust hoop strike 
  • After installation, check door alignment and door seal pressures

Note: TriMark hoop strikes are designed and tested to meet or exceed FMVSS 206 safety requirements only when used with TriMark's corresponding FMVSS 206 compliant latches.

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

070-1000 8mm Hoop Strike

Please specify search criteria:


CompareCatalog NumberTriMark NumberDescriptionStatus CodeSample RequestCAD Drawing
0701000-015-010135284-01Zinc Plate/Clear Chromate,43mm,57mmA/A
0701000-015-0101 no offset38709-01Zinc Plate/Clear Chromate,43mm,57mmA/A
0701000-015-020234119-01Zinc Plate/Clear Chromate,47mm,69mmA/A
0701000-015-0202 Slotted Mounting Holes39390-01Zinc Plate/Clear Chromate,47mm,69mmA/A
0701000-087-010137434-01Black E-coat,43mm,57mmA/A
0701000-087-020237435-01Black E-coat,47mm,69mmA/A
©2021 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale