070-0400 12mm Diameter Striker Bolt

Designed as a companion part for use with TriMark's single rotor latches and cage nuts that requires a 12mm (.472") diameter striker bolt.

Material

  • AISI 4140 steel heat treated

Installation

  • Torque to 35 ft-lbs (46.7 N-m) minimum depending upon surface conditions

Finish

  • Zinc plated with clear chromate

Caution: TriMark striker bolts are designed and tested to meet or exceed FMVSS 206 (ECE R11) safety requirements only when used with TriMark's corresponding FMVSS 206 (ECE R11) compliant latches. Note that some of the longer striker bolts have diminished load values in certain latch families. Please check with TriMark Engineering before finalizing your striker selection requiring FMVSS 206 (ECE R11) compliance.

Latch & Striker Installation

  • Install striker bolt in door frame
  • Close door carefully and check for interference between head of striker bolt and latch components
  • Add or remove shims under striker bolt washer as required (outside diameter of shim should be larger than outside diameter of striker bolt washer)
  • Adjust striker bolt vertically so door is not guided upward or downward while being closed
  • CHECK TO DETERMINE THAT BOTH SECONDARY AND PRIMARY LATCHING POSITIONS ARE USABLE
  • Door should be latched but not "closed" in secondary position with respect to adjacent surfaces in primary position
  • If both primary and secondary positions are not evident, readjust striker bolt
  • After installation, check door alignment and door seal pressures

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

070-0400 12mm Diameter Striker Bolt

Please specify search criteria:


CompareCatalog NumberTriMark NumberShoulder DiameterThread SizeInstalled LengthThread LengthDrive Detail Internal or ExternalWasher Dia. X ThicknessStriker GuardStatus CodeSample RequestCAD Drawing
0700400-00-00-102-0000-00-00-122420-01 NA None 1.02 NA NA NA YesA/A
0700400-00-00-142-0000-00-00-122421-01 NA None 1.42 NA NA NA YesA/A
0700400-03-00-181-0000-00-03-220774-01 0.472 None 1.81 NA NA 0.25 Thick Hoop Strike Mount Plate Hoop StrikeA/A
0700400-03-03-102-0638-04-00-016904-01 0.472  1.02 0.638 0.312 Internal NA NoA/A
0700400-03-06-146-0787-06-00-050734-01 0.472 M12 X 1.75-6g 1.46 0.787 0.750 External NA NoA/A
0700400-03-07-088-1084-09-00-032056-01 0.472 M10 X 1.5-6g 0.88 1.084 M10 X 1.5-6g External thread NA NoA/A
0700400-03-07-098-0709-10-00-022418-01 0.472 M10 X 1.5-6g 0.98 0.709 0.630 external NA NoA/A
0700400-03-07-117-0879-09-02-036707-01 0.472 M10 X 1.5-6g 1.17 0.879 M10 X 1.5-6g External thread 0.79 X 0.11 NoA/A
0700400-03-07-138-0709-10-00-022419-01 0.472 M10 X 1.5-6g 1.38 0.709 0.630 external NA NoA/A
0700400-03-07-148-0604-09-02-031364-01 0.472 M10 X 1.5-6g 1.48 0.604 M10 X 1.5-6g External thread 0.79 X 0.11 NoA/A
0700400-03-07-158-0709-08-02-150995-01 0.472 M10 X 1.5-6g 1.58 0.709 8mm Internal 0.79 X 0.11 YesA/A
©2024 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale