050-0200 Slimline Rotary Latch

This compact single rotor latch is designed for light to medium applications for on or off highway entrance doors, compartments and access panels. It features a variety of trip levers and mounting axles for ease of mounting and application and is FMVSS 206 (ECE R11) compliant.

Designed For

  • Thin, light or medium weight door applications
  • Door weights up to 75 lbs. (34 kg)
  • Door seal pressures of 20-25 lbs. (9-11 kg) recommended for best results (not to exceed 50 lbs. (23 kg)
  • Visible surface installation or concealed installation

Available

  • Left or right hand configurations (left hand shown)
  • With standard .265" (6.7mm) diameter "thru" axles as shown, 1/4-20 UNC threaded axles or M6 x 1.0 threaded axles

Finish

  • Zinc plated, clear chromate steel components
  • Stainless steel

Material

  • Internal latch components: Heat treated smooth edge stamped steel
  • Springs: Non-corrosive stainless steel
  • Case halves: High strength steel

Internal Lubrication

  • Oven-cured dry lubricant is applied on all critical moving parts

Installation

  • (3) 1/4-20 UNC grade 5-type or M6 x 1 class 8.8 or better fasteners are recommended
  • Vertical mounting with support ramp at top is required for proper alignment and subsequent engagement of locking pawl and striker bolt
  • Tighten to the fastener manufacturers' recommended torque value, however, do not exceed 120 in-lbs. (13.3 N-m)
  • Note: In order to pass the FMVSS 206 strength requirement for this latch family, latches that contain 1/4 -20 UNC or M6 x 1.0 threaded axles must utilize fasteners that have sufficient length so that the end of the fastener passes completely through the entire axle and extend beyond the outside surface of the latch case


U.S. Patent No. 7,156,430 / 7,320,488

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

Caution: Applications of this latch may fall within the requirements of FMVSS 206 (ECE R11) and SAE J839 safety standards. These safety related requirements are dependent on door application, e.g. front and rear hinged doors, sliding doors, or hinged upward swinging doors. The entire door hardware system must be included in the design/analysis process: latch, handle, lock mechanism, cables/rods/linkages, fasteners, hinges, etc. This ensures compatibility of all components within the hardware system. If FMVSS 206 (ECE R11) is a requirement, then all of the components within the door system must comply with strength, inertia and locking requirements as specified within the Standard. Note that this product complies with FMVSS 206 (ECE R11) when tested with approved TriMark Striker Bolts in accordance with SAE J839 and that this product meets FMVSS 206 (ECE R11) load requirements and may be used in FMVSS 206 (ECE R11) applications pending TriMark application approval

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

050-0200 Slimline Rotary Latch

  • Agricultural Tractor / Combine

    Access Panels

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Bus / Motorcoach / Mass Transit

    Access Panels

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Construction - Heavy Earthmoving

    Access Panels

    Engine Compartments / Hoods


  • Construction - Lifting and Material Handling

    Access Panels

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Construction - Light Earthmoving

    Access Panels

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Fire / Rescue / Ambulance / Emergency Vehicle

    Access Panels

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Heavy Truck / Sleeper Cabs

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments

    Tool Boxes


  • Industrial Enclosure/Cabinet

    Access Panels/Cabinet Doors

    Exterior Storage Compartments


  • Motor Homes

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Personnel Doors


  • Power Sports

    Access Panels

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments

    Tool Boxes


  • Replicars / Kit Cars

    Engine Compartments / Hoods

    Exterior Personnel Doors


  • Step Van / Walk-in Vans / Delivery Vehicle

    Exterior Personnel Doors

    Exterior Storage Compartments

    Tool Boxes


  • Trailers - Ranch / Farm / Cargo / Utility

    Access Panels

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Travel Trailer / 5th Wheel

    Baggage Doors

    Exterior Personnel Doors


  • Utility Bodies / Wreckers / Specialty Truck

    Exterior Storage Compartments

    Tool Boxes


Please specify search criteria:


CompareCatalog NumberTriMark NumberHandingMountingActuationActuation FeatureFront PlateStatus CodeCAD Drawing
0500200-1-01-1215716-00-112159-16 Right Hand 1/4-20 UNC Threaded Axles L-Shaped, Non-Handed, 1.56 X .16 (39.6mm X 4.1mm), Stop No Actuation Feature StandardA/A
©2024 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale