050-0100 Two Rotor Latch

This versatile two rotor latch is designed for medium to heavy-duty applications for on or off highway entrance doors, compartments and access panels. It features a variety of trip levers and mounting axles for ease of mounting and applications and is FMVSS 206 (ECE R11) compliant.

 

 

Designed For

  • Door thicknesses of 1-7/8" (47.6mm) or greater
  • Door weights of 50-200 lbs. (23-91 kg)
  • Door seal pressures of 50-150 lbs. (23-68 kg) (suggested for best results)
  • Use with TriMark 070-0200 Striker Bolt 

Available

  • In left or right hand configurations (right hand shown)
  • With (4) 1/4-20 UNC or M6 x 1 threaded axles
  • With trip lever options
  • Straddle mount option

Material

  • Internal latch components: heat treated, smooth edge stamped steel
  • Case halves: high strength steel
  • Springs: non-corrosive stainless steel

Finish

  • Zinc plated, clear chromate steel components

 


Installation

  • (4) 1/4-20 UNC grade 5 or M6 x 1 class 8.8 or better fasteners are required (not included)
  • Tighten to the fastener manufacturers' recommended torque value, however, do not exceed 120 in-lbs (13.3 N-m)
  • Fastener mounting holes diameter should not exceed .281" (7.1mm)

Internal Lubrications

  • Oven-cured dry lubricant is applied at factory on all critical moving parts

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

 Applications of this latch may fall within the requirements of FMVSS 206 (ECE R11) and SAE J839 safety standards. These safety related requirements are dependent on door application, e.g. front and rear hinged doors, sliding doors, or hinged upward swinging doors. The entire door hardware system must be included in the design/analysis process: latch, handle, lock mechanism, cables/rods/linkages, fasteners, hinges, etc. This ensures compatibility of all components within the hardware system. If FMVSS 206 (ECE R11) is a requirement, then all of the components within the door system must comply with strength, inertia and locking requirements as specified within the Standard. Note that this product complies with FMVSS 206 (ECE R11) when tested with approved TriMark Striker Bolts in accordance with SAE J839 and that this product meets FMVSS 206 (ECE R11) load requirements and may be used in FMVSS 206 (ECE R11) applications pending TriMark application approval.

 

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

050-0100 Two Rotor Latch

  • Agricultural Tractor / Combine

    Access Panels

    Door Hold Open

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Bus / Motorcoach / Mass Transit

    Access Panels

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Construction - Heavy Earthmoving

    Access Panels

    Door Hold Open

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Construction - Lifting and Material Handling

    Access Panels

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Construction - Light Earthmoving

    Access Panels

    Door Hold Open

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Fire / Rescue / Ambulance / Emergency Vehicle

    Access Panels

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Heavy Truck / Sleeper Cabs

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Industrial Enclosure/Cabinet

    Access Panels/Cabinet Doors

    Exterior Storage Compartments


  • Motor Homes

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Personnel Doors


  • Replicars / Kit Cars

    Engine Compartments / Hoods

    Exterior Personnel Doors


  • Step Van / Walk-in Vans / Delivery Vehicle

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Trailers - Ranch / Farm / Cargo / Utility

    Access Panels

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Travel Trailer / 5th Wheel

    Baggage Doors

    Exterior Personnel Doors


  • Utility Bodies / Wreckers / Specialty Truck

    Exterior Storage Compartments


Please specify search criteria:


CompareCatalog NumberTriMark NumberHandingMountingActuationActuation FeatureActuation SupportStatus CodeSample RequestCAD Drawing
0500100-101-11235-0111644-16 Right Hand 1/4-20 UNC Threaded Axles Straight, Non-Handed, 2.35 X .28 X .24 Dia Hole (59.7mm X 7.1mm X 6.1mm) No Actuation Feature Standard MountA/A
0500100-101-11280-0111465-16 Right Hand 1/4-20 UNC Threaded Axles Straight, Right Hand, 1.10 X .14 X .24 Dia Hole (27.9mm X 3.6mm X 6.1mm), Spring Hole No Actuation Feature Standard MountA/A
0500100-101-11282-0111471-16 Right Hand 1/4-20 UNC Threaded Axles Straight, Right Hand, 1.10 X .14 X .28 Dia Hole (27.9mm X 3.6mm X 7.1mm), Spring Hole No Actuation Feature Standard MountA/A
0500100-101-14153-0116592-01 Right Hand 1/4-20 UNC Threaded Axles 2-Point, Right Hand Actuator, 1.55 X .05 X .24 Dia Hole (39.4mm X 1.3mm X 6.1mm), .49 X 1.39 X .24 Dia Hole (12.4mm X 35.3mm X 6.1mm), Spring Hole No Actuation Feature Standard MountA/A
0500100-101-81033-3111538-16 Right Hand 1/4-20 UNC Threaded Axles L-Shaped Finger Release, Right Hand, 3.50 (88.9mm) Wave Washer Standard MountA/A
0500100-101-81185-0111945-16 Right Hand 1/4-20 UNC Threaded Axles 2-Point, Non-Handed, 1.25 X 0.63 X 1.08 X .25 Dia Hole (31.8mm X 16.0mm X 27.4mm X 6.4 mm) No Actuation Feature Standard MountA/A
0500100-102-11280-0111878-01 Right Hand 0.286 (7.3mm) Diameter Through Axles Straight, Right Hand, 1.10 X .14 X .24 Dia Hole (27.9mm X 3.6mm X 6.1mm), Spring Hole No Actuation Feature Standard MountA/A
0500100-102-11280-1112057-16 Right Hand 0.286 (7.3mm) Diameter Through Axles Straight, Right Hand, 1.10 X .14 X .24 Dia Hole (27.9mm X 3.6mm X 6.1mm), Spring Hole Torsion Spring Standard MountA/A
0500100-102-11281-0111451-16 Right Hand 0.286 (7.3mm) Diameter Through Axles Straight, Right Hand, 1.10 X .14 X .27 Dia Hole (27.9mm X 3.6mm X 6.9mm ), Spring Hole No Actuation Feature Standard MountA/A
0500100-102-11281-01 Finish14890-02 Right Hand 0.286 (7.3mm) Diameter Through Axles Straight, Right Hand, 1.10 X .14 X .27 Dia Hole (27.9mm X 3.6mm X 6.9mm ), Spring Hole No Actuation Feature Standard MountA/A
0500100-102-11281-01 Low Gloss Black14890-01 Right Hand 0.286 (7.3mm) Diameter Through Axles Straight, Right Hand, 1.10 X .14 X .27 Dia Hole (27.9mm X 3.6mm X 6.9mm ), Spring Hole No Actuation Feature Standard MountA/A
0500100-102-11396-0111490-01 Right Hand 0.286 (7.3mm) Diameter Through Axles Straight, Right Hand, .72 X .19 X .24 Dia Hole (18.3mm X 4.8mm X 6.1mm) No Actuation Feature Standard MountA/A
0500100-102-80647-0111450-16 Right Hand 0.286 (7.3mm) Diameter Through Axles L-Shaped, Non-Handed, 1.87 X .89 X .28 Dia Hole (47.5mm X 22.6mm X 7.1mm), Spring Hole No Actuation Feature Standard MountA/A
0500100-102-81021-0111458-16 Right Hand 0.286 (7.3mm) Diameter Through Axles L-Shaped, Non-Handed, 1.87 X .89 X .25 Dia Hole (47.5mm X 22.6mm X 6.4mm), Slot No Actuation Feature Standard MountA/A
0500100-102-81634-1112198-01 Right Hand 0.286 (7.3mm) Diameter Through Axles L-Shaped, Right Hand, with Slot, 2.00 X .00 X .24 Dia Hole (50.8mm X .0mm X 6.1mm) Torsion Spring Standard MountA/A
0500100-106-11235-0118199-01 Right Hand M6 X 1.0 Threaded Axles Straight, Non-Handed, 2.35 X .28 X .24 Dia Hole (59.7mm X 7.1mm X 6.1mm) No Actuation Feature Standard MountA/A
0500100-106-11280-0112093-16 Right Hand M6 X 1.0 Threaded Axles Straight, Right Hand, 1.10 X .14 X .24 Dia Hole (27.9mm X 3.6mm X 6.1mm), Spring Hole No Actuation Feature Standard MountA/A
0500100-106-11280-1111831-01 Right Hand M6 X 1.0 Threaded Axles Straight, Right Hand, 1.10 X .14 X .24 Dia Hole (27.9mm X 3.6mm X 6.1mm), Spring Hole Torsion Spring Standard MountA/A
0500100-106-11281-1115507-01 Right Hand M6 X 1.0 Threaded Axles Straight, Right Hand, 1.10 X .14 X .27 Dia Hole (27.9mm X 3.6mm X 6.9mm ), Spring Hole Torsion Spring Standard MountA/A
0500100-106-16414-2116296-01 Right Hand M6 X 1.0 Threaded Axles L-Shaped, Right Hand, 2 point with Slot, 1.01 x 1.28 x .24 Dia Hole (25.7mm X 32.5mm X 6.1mm), Spring Hole Extension Spring Standard MountA/A
0500100-106-17728-1117727-01 Right Hand M6 X 1.0 Threaded Axles Straight Finger Release, Right Hand Lever, 1.95 (49.5mm) Torsion Spring Standard MountA/A
0500100-106-80813-0112180-16 Right Hand M6 X 1.0 Threaded Axles Straight Finger Release, Non-Handed, 2.81 (71.4mm) No Actuation Feature Standard MountA/A
0500100-106-81021-0112991-01 Right Hand M6 X 1.0 Threaded Axles L-Shaped, Non-Handed, 1.87 X .89 X .25 Dia Hole (47.5mm X 22.6mm X 6.4mm), Slot No Actuation Feature Standard MountA/A
0500100-106-81185-01 .237 Dia Holes18611-02 Right Hand M6 X 1.0 Threaded Axles 2-Point, Non-Handed, 1.25 X 0.63 X 1.08 X .25 Dia Hole (31.8mm X 16.0mm X 27.4mm X 6.4 mm) No Actuation Feature Standard MountA/A
0500100-106-81185-01 .250 Dia Holes18611-01 Right Hand M6 X 1.0 Threaded Axles 2-Point, Non-Handed, 1.25 X 0.63 X 1.08 X .25 Dia Hole (31.8mm X 16.0mm X 27.4mm X 6.4 mm) No Actuation Feature Standard MountA/A
0500100-201-11277-0211466-16 Left Hand 1/4-20 UNC Threaded Axles Straight, Left Hand, 1.10 X .14 X .24 Dia Hole (27.9mm X 3.6mm X 6.1mm), Spring Hole No Actuation Feature Straddle MountA/A
0500100-201-11279-0111448-16 Left Hand 1/4-20 UNC Threaded Axles Straight, Left Hand, 1.10 X .14 X .28 Dia Hole (27.9mm X 3.6mm X 7.1mm), Spring Hole No Actuation Feature Standard MountA/A
0500100-201-50011-0111453-16 Left Hand 1/4-20 UNC Threaded Axles Straight Finger Release, Non-Handed, 2.81 (71.4mm) No Actuation Feature Standard MountA/A
0500100-201-81185-0111946-16 Left Hand 1/4-20 UNC Threaded Axles 2-Point, Non-Handed, 1.25 X 0.63 X 1.08 X .25 Dia Hole (31.8mm X 16.0mm X 27.4mm X 6.4 mm) No Actuation Feature Standard MountA/A
0500100-202-11034-0111454-16 Left Hand 0.286 (7.3mm) Diameter Through Axles L-Shaped, Left Hand, 2.11 X .51 X .28 Dia Hole (53.6mm X 13.0mm X 7.1mm) Offset No Actuation Feature Standard MountA/A
0500100-202-11235-0111470-16 Left Hand 0.286 (7.3mm) Diameter Through Axles Straight, Non-Handed, 2.35 X .28 X .24 Dia Hole (59.7mm X 7.1mm X 6.1mm) No Actuation Feature Standard MountA/A
0500100-202-11277-0111879-01 Left Hand 0.286 (7.3mm) Diameter Through Axles Straight, Left Hand, 1.10 X .14 X .24 Dia Hole (27.9mm X 3.6mm X 6.1mm), Spring Hole No Actuation Feature Standard MountA/A
0500100-202-11278-0111464-16 Left Hand 0.286 (7.3mm) Diameter Through Axles Straight, Left Hand, 1.10 X .14 X .27 Dia Hole (27.9mm X 3.6mm X 6.9mm) Offset, Spring Hole No Actuation Feature Standard MountA/A
0500100-202-31479-2131481-01 Left Hand 0.286 (7.3mm) Diameter Through Axles L-Shaped, Non-Handed, .85 (21.55mm), Spring Hole Extension Spring Standard MountA/A
0500100-202-80645-3111447-16 Left Hand 0.286 (7.3mm) Diameter Through Axles L-Shaped Finger Release, Left Hand, 3.50(88.9mm) Wave Washer Standard MountA/A
0500100-202-80647-0111449-16 Left Hand 0.286 (7.3mm) Diameter Through Axles L-Shaped, Non-Handed, 1.87 X .89 X .28 Dia Hole (47.5mm X 22.6mm X 7.1mm), Spring Hole No Actuation Feature Standard MountA/A
0500100-202-81021-0111457-16 Left Hand 0.286 (7.3mm) Diameter Through Axles L-Shaped, Non-Handed, 1.87 X .89 X .25 Dia Hole (47.5mm X 22.6mm X 6.4mm), Slot No Actuation Feature Standard MountA/A
0500100-206-11235-0118200-01 Left Hand M6 X 1.0 Threaded Axles Straight, Non-Handed, 2.35 X .28 X .24 Dia Hole (59.7mm X 7.1mm X 6.1mm) No Actuation Feature Standard MountA/A
0500100-206-11277-0117955-01 Left Hand M6 X 1.0 Threaded Axles Straight, Left Hand, 1.10 X .14 X .24 Dia Hole (27.9mm X 3.6mm X 6.1mm), Spring Hole No Actuation Feature Standard MountA/A
0500100-206-11278-0114120-01 Left Hand M6 X 1.0 Threaded Axles Straight, Left Hand, 1.10 X .14 X .27 Dia Hole (27.9mm X 3.6mm X 6.9mm) Offset, Spring Hole No Actuation Feature Standard MountA/A
0500100-206-11278-2119355-01 Left Hand M6 X 1.0 Threaded Axles Straight, Left Hand, 1.10 X .14 X .27 Dia Hole (27.9mm X 3.6mm X 6.9mm) Offset, Spring Hole Extension Spring Standard MountA/A
0500100-206-11279-4219369-01 Left Hand M6 X 1.0 Threaded Axles Straight, Left Hand, 1.10 X .14 X .28 Dia Hole (27.9mm X 3.6mm X 7.1mm), Spring Hole Rod Collar Straddle MountA/A
0500100-206-12718-1129760-01 Left Hand M6 X 1.0 Threaded Axles L-Shaped Finger Release, Left Hand, 2.00 (50.8mm) Torsion Spring Standard MountA/A
0500100-206-16415-2116297-01 Left Hand M6 X 1.0 Threaded Axles L-Shaped, Left Hand, 2 point with Slot, 1.01 x 1.28 x .24 Dia Hole (25.7mm X 32.5mm X 6.1mm), Slot, Spring Hole Extension Spring Standard MountA/A
0500100-206-33185-1133186-01 Left Hand M6 X 1.0 Threaded Axles L-Shaped Finger Release, left hand, 92mm X 42mm Torsion Spring Standard MountA/A
0500100-206-80813-0112181-16 Left Hand M6 X 1.0 Threaded Axles Straight Finger Release, Non-Handed, 2.81 (71.4mm) No Actuation Feature Standard MountA/A
0500100-206-80973-1117726-01 Left Hand M6 X 1.0 Threaded Axles Finger Release, Left Hand, 1.91 (48.5mm) Torsion Spring Standard MountA/A
0500100-206-81167-02TME12680-01 Left Hand M6 X 1.0 Threaded Axles L-Shaped, Left Hand, 4.59 X 1.51 (116.6mm X 38.4mm), Spring Hole, Offset No Actuation Feature Straddle Mount A/CP
0500100-206-81185-01 .250 Dia Holes18610-01 Left Hand M6 X 1.0 Threaded Axles 2-Point, Non-Handed, 1.25 X 0.63 X 1.08 X .25 Dia Hole (31.8mm X 16.0mm X 27.4mm X 6.4 mm) No Actuation Feature Standard MountA/A
0500100-206-81684-2112196-16 Left Hand M6 X 1.0 Threaded Axles L-Shaped, Non-Handed, 1.87 X 1.13 X .25 Dia Hole (47.5mm X 28.7mm X 6.4mm), Spring Hole Extension Spring Standard MountA/A
©2018 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale